Slideshow: First Solar’s CTO on CadTel and Silicon PV Under One Roof

By PI News Feed on September 30, 2013 • ( Leave a comment )

[pagebreak:FSLR]

Raffi Garabedian, the CTO of thin-film solar giant First Solar, spoke at an IEEE Silicon Valley solar event earlier this month in a talk entitled,"CdTe and c-Si Under One Roof."

The immediate issues Garabedian addressed:

— Is First Solar abandoning CdTe in favor of c-Si — because the CdTe roadmap is not competitive? (the answer is no.)

— Why invest in a new c-Si technology — when there’s already so much capacity?

The response is that one technology won’t win in all segments. The CTO said, "For one of the top 5 solar companies in the world — it’s pretty obvious we should have a diverse technology portfolio."

He said that First Solar can’t make money reselling Chinese panels. He added that the Chinese can’t make money selling Chinese panels.

Garabedian said, "It’s about time" for First Solar to have an entry in the "space-constrained" market.

The CTO notes that large commercial and utility-scale solar is driven by IRR economics.

While the right side of the following chart, in residential and small commercial, is driven by different economics. He added, "We don’t have a product that plays well in restricted spaces." He said it comes down to efficiency and customer behavior, adding, "We need more than one solution if were going to continue to be a very big player in the PV module market."

"At the utility scale, efficiency is really hard to pay for." said the CTO, adding, "You end up paying too much for the module that doesn’t offset your balance of system (BoS) costs." Garabedian said, "We are at 2 cents [per watt] of balance of system cost reduction for every absolute one percent efficiency improvement."

(He adds that he doesn’t understand the economics of SunPower’s C7 tracker)

The following graph on LCOE for different generation technologies shows "the LCOE for c-Si PV tends to be slightly higher than for thin film but that can be improved with tracking." He noted there would be a similar improvement for thin film on trackers.

For Garabedian — this shows that "High-efficiency doesn’t mean low-cost at the utility scale."

Here’s Garabedian on cadmium telluride’s solar conversion efficiency:

"CdTe and GaAs: you can’t get better than those two materials from a Shockley-Queisser limit perspective. It’s perfectly matched to the solar spectrum. In fact, we can push the bandgap one way or another by adding a sprinkle of this or a sprinkle of that and get even more. The problem is cadtel is a polycrystalline material. It’s messy, so there are a lot of losses. That’s bad news, but it’s also good news, because it means my team has a long way to go from a 13 percent module (which is kind of what we produce day-in and day-out today) to where I believe the entitlement is, which is over 18 percent module efficiency. By the way, we’ve made a 16.1 percent module, so we know how to do it. We just have some more work to do to get it into production."

He added, "The real advantage of cadtel is not efficiency — it’s cost."

Garabedian (after reminding us of public company disclosure disclaimers) said that "the bottom line is, by 2017, we’ll be in the low-30 cents per watt range." That figure is on the lower end of the “Production Cost” (not inclusive of Cost of Sales) which First Solar announced on its Analyst Day earlier this year.

He added, "It’s polycrystalline, so it’s all about recombination losses at the end of the day for us. Everywhere on the device — the front, back, and middle. We do spend a lot of time working on lifetimes, a lot of time working on passivation, on interfaces, and on bandgap engineering these days."

First Solar recently acquired GE’s CdTe technology, allowing Garabedian to claim the current 19.6 percent cell record.

Garabedian said, "A 17 [percent] to 18 percent [efficient] module is within our reach with today’s technology."

Next, Garabedian talks about silicon solar technology startup Tetrasun, a recent acquisition by First Solar.

[pagebreak: FSLR2]

"Tetrasun is a company we purchased to address space-constrained markets," with a high-efficiency, n-type mono cell technology, according to First Solar’s CTO.

The Tetrasun cell is bifacial copper metallization built on n-type mono. "The core cell technology is a very unique passivation material system."

"The pricing premium is huge between Chinese tier one" and high-efficiency mono at 18 percent and 19 percent efficiency — 30 cents and 70 cents respectively.

An analysis by First Solar shows that going from a 16 percent to a 20 percent module enables a BoS savings of "16 cents plus or minus ten cents" depending on location. According to Garabedian, the rest of that 70 cents premium comes from channel control, systems level sales, segment strategy and strategic relationships.

"So we’re motivated to go out for a very high efficiency cell technology — but not at all costs," said the CTO, adding, "We intentionally didn’t acquire a company that has an advanced interdigitated back contact cell that can get [First Solar] up to 23 percent. Why? Because I don’t think I can afford all those process steps it takes to make that cell and still sell into these markets. We took a very pragmatic approach to find the sweet spot between efficiency upside and the underlying cost structure of cell manufacture. We think we have that with this product."

"Why n-type? That’s the only way you get up above 20 percent. Really, practically n-type is the only way you get there."

Garabedian said that First Solar looks forward to introducing the silicon product to the market next year.

The CTO of the world’s largest solar EPC and largest thin-film vendor left the crowd with these thoughts:

"I think that we are looking at a future where established PV companies are going to be unable to innovate internally, simply because the budget isn’t there, because the margins are too thin. That’s bad news for the industry overall. We’re seeing it in China. We’re seeing an incremental approach to technology improvement — which has taken us a long way particularly in terms of cost. But it isn’t going to take us much further in terms of performance and further cost reduction."

"The message I want to give — this is an incredibly fruitful time to be a startup in core PV technology. If there are any investors with reputable venture firms – they’ll say I’m crazy because no one is investing in materials or devices or hardware of any kind."

"I want to see a lot of investments made in next-generation and future-generation PV technologies. There’s room for innovation across the entire value chain and I think there’s tons of room in cell and module — and that’s the piece of the pie where I see the least investment today. I see a lot investors going for the easy money, taking the easy way out — in electronics and mechanics — stuff that can be developed quickly and turned quickly."

"But the hard work that needs to be done isn’t getting done because there’s a lack of funding for it."

"I’m a huge optimist. I think we’ll have 30 percent efficiency modules in ten years. I just don’t know how we’re going to get there. But I’m very eager to buy one."